Fisher & Paykel DD24DCTW9 Tall Double DishDrawer Dishwasher
Tall double-drawer dishwasher; typical trouble is dishes that stay damp or a drawer that stops mid-cycle.
Model overview
The DD24DCTW9 is a tall double DishDrawer dishwasher from Fisher & Paykel in the Contemporary range, with two drawers stacked in one cavity. Its width is 23 9/16 inches and its depth is 22 9/16 inches, with a maximum drawer extension of 21 9/16 inches. A minimum cavity height of 34 inches and a minimum cavity depth of 22 1/16 inches decide whether the unit fits. Across the metro areas we cover, owners most often report dishes that come out damp or a cycle that will not finish. For the booking form, describe the symptom, copy the full number from the data label, and list any code the controls show.
At a glance
| Model | DD24DCTW9 |
|---|---|
| Appliance | 24-inch Tall Double DishDrawer Dishwasher |
| Common symptoms | dishes not getting clean or dry; door latch or control panel problems; cycle stops early or will not start; water left in the tub after the cycle |
| What you can check | Note the cycle used, whether water is left in the tub, and any code or flashing light. |
| When to call a technician | If the symptom comes back after the simple checks, or you see a code, leaking water or a burning smell, book a visit. |
Specifications
| Dimensions | Height with mounted feet is 34–36 3/8 inches. Depth is 22 9/16 inches. Maximum drawer extension is 21 9/16 inches. Width is 23 9/16 inches. |
|---|---|
| Installation | Minimum cavity height is 34 inches. Cavity width is 23 5/8 inches. Minimum cavity depth is 22 1/16 inches. |
| Features | Two-drawer tall configuration. |
What sets the DD24DCTW9 apart
The tall two-drawer configuration matters most, because a standard single-drawer cavity cannot take a second drawer. Cavity width and minimum depth are measured on site, so the dimensions are checked before the unit goes in. The drawers pull out to full extension to load, which is why the cavity depth needs margin behind the front.
Service notes for the DD24DCTW9
Dishes that come out damp or dirty usually trace to a blocked spray arm, a clogged filter or a drying fan that stops early, so a technician checks those before the controls. A cycle that stops early or will not start points to the drawer latch or the control panel, which reports each drawer position to the controller. Water left in the tub often means a drain path problem, a kinked hose or a drain pump that is not clearing. Before the visit, the owner can clear the filter, spin each spray arm, and confirm the drawer closes all the way until the latch clicks. Switch the unit off at the breaker before removing filters or the kickplate.
The model number is printed on the rating label, usually on the edge of the door or the side of the tub, visible when the door is open; match it letter for letter before booking, because a single letter can change parts.
Frequently asked questions
What minimum cavity height does the DD24DCTW9 need?
The cavity must be at least 34 inches tall, and the minimum cavity depth is 22 1/16 inches.
How far does a drawer on the DD24DCTW9 pull out?
The maximum drawer extension is 21 9/16 inches, so check the room in front of the cabinet.
Where do I find the full DD24DCTW9 model number?
Check the rating label on the edge of the door or the side of the tub, visible when the door is open. Copy every letter and digit, including the ones at the end.
Do you repair the Fisher & Paykel DD24DCTW9 at home?
Yes. We book in-home visits for this model in the Miami, New York, Houston, Los Angeles and San Diego metro areas. Add the model number and the symptom to the booking form.
Common issues for this model
- Dishes not getting clean or dry
- Door latch or control panel problems
- Cycle stops early or will not start
- Water left in the tub after the cycle
Related error codes
Fisher & Paykel DishDrawer F3 Code: Water Temperature Fault
F3 is a temperature fault. What the 65 C limit means and who to call if it persists.
Fisher & Paykel DishDrawer E4 Code: Heating Element
E4 is a failed heating element. One reset, then disconnect and call; avoid the filter plate.
Fisher & Paykel DishDrawer U6 and A6 Codes: Spray Arm
A6 on newer panels and U6 on Classic ones: the spray arm or low water pressure.
Fisher & Paykel DishDrawer A1 Code: Water Supply Fault
A1 signals a water supply fault. Open the supply and clear the code with Start/Pause.
Recommended repair service
DishDrawer Repair
DishDrawer not draining, not filling, leaking, or showing a fault code? We diagnose Fisher & Paykel drawer dishwashers.
Troubleshooting resources
Note the cycle used, whether water is left in the tub, and any code or flashing light.
Model-information disclaimer. Confirm your exact model number and specifications with your appliance documentation before booking a repair. Model pages are for identification and compatibility reference.
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.