Skip to content
Same-day and next-day appointments in most areas.
Specialized Fisher & Paykel repair service. Experienced technicians, genuine parts, service across major U.S. metro areas.
Error Code

Fisher & Paykel DishDrawer F1 Code: Flood Detected

Error code F1 / E1
Appliance DishDrawer Dishwasher
Quick answer

F1 means flood detected or excess foaming. Steps for a wet floor and for a dry drawer.

Model compatibility: Fisher & Paykel reuses codes across series and model years, so F1 / E1 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Plain language

What this code means

Flood detected or excess foaming; flood switch activated.

If water is on the floor

Switch off the power and the water supply, then book a service. The two manufacturer documents are in step here: the old guide wants the water shut off and a call to the service centre or Customer Care, and the support article gives matching advice. Never run repeated restarts while water stands near the machine.

At a glance

Code F1 / E1
What it means Flood detected or excess foaming; flood switch activated.
What you can check If the base is dry, switch off the power and leave the unit off until morning, then run one cycle with no detergent. If the code is gone, foam was probably the cause, so use no more than one teaspoon of detergent.
When to call a technician If you see water on the floor, switch off the power and the water supply and book a service visit. An F1 that still appears after the empty cycle also needs a service visit.

What F1 stands for

In the DD24/DD60 guide, F1 means the flood switch has been triggered. The support article words it “flood detected or excess foaming”, which tells you suds can trip the switch just like water. Some panels and listings show E1 for the same fault.

When everything is dry

Support gives a gentle way of finding out whether foam was to blame:

  1. Isolate the DishDrawer from its power supply.
  2. Leave it like that until morning.
  3. Next day, run one cycle with no detergent.
  4. If the code is gone, foam was probably the trigger, and detergent should be limited to one teaspoon at most.

If the empty cycle still produces F1, no other owner steps are published and a service visit is the logical next move.

Why the amount of detergent matters

Dishwasher detergent is designed to clean with little foam. An oversized dose, or hand-washing liquid, makes more suds than the DishDrawer can manage. A7 is a related foam warning, one that resets by itself through an auto recovery program.

Inspection and cautions

What separates the two cases in the documents is whether you can see water, so inspect the tub, the cabinet base and the floor around it. Water in sight: cut power and water, then book. Leave electrical panels shut instead of hunting for the switch, and take a dry F1 that keeps coming back seriously, since the guide never calls it harmless.

FAQ

Does every F1 mean water has leaked?
No. Excess foaming is the other cause the support article gives.

Is it fine to dry the base and keep going?
Only when there was no visible water and the overnight test removes the code. If not, book a service.

See also

  • E1: Classic panels, “flood detected”
  • A3: the drawer is not draining, another case of water where it should not be

Flood and leak repair in our metro areas

Our DishDrawer service covers the Miami, New York, Houston, Los Angeles and San Diego metro areas. For an F1 with water on the floor, shut off the supply first and then ring (844) 659-2290. Have to hand the number of drawers, the amount of detergent used and what the overnight test showed.

Source: Fisher & Paykel DishDrawer DD24 and DD60 user guide (590030A); Fisher & Paykel Support, F-code displaying on DishDrawer

Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

References

Sources & references

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Miami, New York, Houston, Los Angeles and San Diego metro areas.
Response time Same-day and next-day appointments in most areas.
Call Book diagnosis