Skip to content
Same-day and next-day appointments in most areas.
Specialized Fisher & Paykel repair service. Experienced technicians, genuine parts, service across major U.S. metro areas.
Error Code

Fisher & Paykel DishDrawer U1 Code: Water Not Reaching Drawer

Error code U1
Appliance DishDrawer Dishwasher
Quick answer

U1 means the drawer got no water. Supply tap, spray arm, and how to drain and restart.

Model compatibility: Fisher & Paykel reuses codes across series and model years, so U1 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Plain language

What this code means

No water: supply not turned on, or spray arm not fitted correctly.

The DishDrawer attempted to fill and did not receive the expected water: that is U1. Two causes are listed. The Classic-model guide says the water supply is not turned on, and the DD24/DD60 guide adds that the spray arm may not be fitted correctly.

At a glance

Code U1
What it means No water: supply not turned on, or spray arm not fitted correctly.
What you can check Open the shut-off valve on the water line to the dishwasher and press start/pause to carry on. Also make sure the spray arm sits properly and rotates freely.
When to call a technician If U1 comes back after both checks, cut the power and water and book a service visit. Tell the technician whether the tub was wet or dry.

Step 1: the tap

  • Locate the shut-off valve on the line to the DishDrawer and make sure it is open.
  • Should it have been shut, open it, then press start/pause so the wash program carries on, as in the Classic guide.
  • Think about whether plumbing work, or a new faucet put in close by, led to it being shut.

Step 2: what is in the drawer?

The DD24/DD60 guide treats two cases separately. A dry tub gets the first list; a puddle left after a failed cycle gets the second. Resist going to the spray arm first with a dry tub, as the guides list the supply as the first cause.

Case A, no water inside

  1. Switch the water supply to the DishDrawer on.
  2. Reconnect the unit by plugging it in or switching it on at the supply.

Case B, water inside

  1. Restore power.
  2. Press the button, then give it half a minute.
  3. Then press the power button. Draining is automatic and lasts roughly two minutes, and steps 2 and 3 may have to be done again.
  4. With the drawer empty, make sure the spray arm sits properly and rotates freely.

The spray arm connection

A badly fitted spray arm is listed under the same fill fault, with no explanation of the link. The arm is what turns and sprays the dishes, and it comes off its mount only when removed on purpose.

Still showing U1

Those two are the owner’s checks. If neither is the problem and U1 comes back, no more owner steps are given; the Classic flowchart says to cut power and water and give Customer Care the code.

FAQ

Does U1 point to a broken inlet valve?
Not in these guides, which mention only the closed supply and the spray arm.

Is the wash program restarted from scratch?
The Classic guide says pressing start/pause resumes it once the water is on.

Related pages

  • A1: supply fault on newer panels, where the tap check also applies
  • U6 / A6: when the arm has come loose or pressure is low
  • A3: water stuck in the drawer

No-water repair across our metro areas

DishDrawer visits are offered in the Miami, New York, Houston, Los Angeles and San Diego metro areas. After the tap and spray arm checks, call (844) 659-2290 and tell us what you tried and whether the tub was wet or dry.

Source: Fisher & Paykel DishDrawer user guide (590199D); DishDrawer DD24 and DD60 user guide (590030A)

Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

References

Sources & references

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Miami, New York, Houston, Los Angeles and San Diego metro areas.
Response time Same-day and next-day appointments in most areas.
Call Book diagnosis