Fisher & Paykel Cooktop E1 Code: Power Supply or Board Error
Two Fisher & Paykel sources, two meanings for E1: a power supply problem and an electronic board or software error.
Model compatibility: Fisher & Paykel reuses codes across series and model years, so E1 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.
What this code means
Care guides list E1 as a problem with the power supply; a full-surface cooktop support article lists it as an electronic board or software error.
Which document are you reading?
An E1 on the display comes with a beep, and the manufacturer’s literature gives two answers.
At a glance
| Code | E1 |
|---|---|
| What it means | E1 points to a power supply problem or to an electronic board or software error, depending on the cooktop. |
| What you can check | Confirm mains power is present: check the wall switch, the breaker and whether the house has an outage. Then hold POWER to switch off and hold it again to restart. |
| When to call a technician | If E1 stays after you take the supply away for a minute and restore it, note the code and call a technician. Wiring at the breaker panel or inside the unit is technician work. |
| Source | Label for E1 | Owner action |
|---|---|---|
| Owner care guides for the induction CI365, CI304, CI244, CI122 and CI905, CI804, CI604, CI302 lines | Power supply trouble | See that the unit is hooked up to mains; find out about an outage in the house or area |
| Support article for the CI926DTB4 full-surface model | A fault in the electronic board or software | Disconnect at the supply, give it 1 minute, switch on |
Neither source says which cooktops belong to which description. Cheapest steps first is the practical answer.
Do these in order
- Establish that mains power is present. A lamp, a clock or another appliance will show it.
- Look at the wall switch and at the breaker; the care guides list both where they discuss a cooktop that will not start.
- Switch off by holding POWER, wait a moment, then hold POWER to start again. According to the guides, that can remove an “E” code.
- If E1 persists, take away the supply entirely for a minute and put it back.
When E1 stays
Record the code and leave it there. The guides direct you to Customer Care or a Fisher & Paykel trained service technician. The support article wants a service repair booked once the code is back despite the one-minute restart. Wiring at the breaker panel or inside the unit is electrician or technician territory.
See also
- E2 gets identical wording in the owner guides.
- E4 is a board error in the support article but overheating in the guides.
Cooktop service in Miami, New York, Houston, Los Angeles and San Diego
If an induction cooktop in one of those metro areas still shows E1, phone (844) 659-2290. Tell the dispatcher about the breaker check and the one-minute restart, and have the model details at hand. The induction cooktop service page describes the service.
Source: Fisher & Paykel Induction Cooktop Care and Maintenance; Induction Cooktop Care Guide 433271A; Support: E6, ER62 or ER21 on full surface induction cooktop
Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.
Sources & references
- Fisher & Paykel Induction Cooktop Care and Maintenance (owner's manual for CI365/CI304/CI244/CI122 models, 2026) - Fault codes; hosted by pcrichard.com
- Fisher & Paykel Induction Cooktop Care Guide 433271A (CI905/CI804/CI604/CI302 models) - Fault codes
- Fisher & Paykel Support: E6, ER62 or ER21 displaying on full surface induction cooktop (CI926DTB4)
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.