Skip to content
Same-day and next-day appointments in most areas.
Independent appliance repair service. We are not affiliated with, authorized by, sponsored by, or endorsed by Fisher & Paykel.
(844) 659-2290
Error Code

Fisher & Paykel Washer 160

Seeing 160 on your Fisher & Paykel Washer? Start with the non-invasive checks below, note the full model/serial, and treat any “exact meaning” as model-dependent until verified for the SmartDrive top-load washer — legacy fault codes platform.

Schedule code diagnosis (844) 659-2290

Reviewed by Ethan Cole · Last reviewed August 10, 2026

Ethan Cole Written by Ethan Cole Appliance Repair Content Specialist Published August 10, 2026 Updated August 11, 2026 Technically reviewed August 10, 2026

Content status: Verified

Error code 160
Appliance Washer
Affected model series SmartDrive top-load washer (verify generation on your serial label)
Quick answer

160 · Washer — cautious homeowner guidance for this display reading (verify for your serial).

Model compatibility: Fisher & Paykel reuses codes across series and model years, so 160 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Plain language

What this code means

This page provides general guidance while 160 is matched to Fisher & Paykel docs for the SmartDrive top-load washer — legacy fault codes platform. Confirm the label on your rating plate before relying on any interpretation.

Signs

Symptoms you may notice

  • The washer display shows 160 during or after a wash cycle.
  • The cycle may pause, stop early, or fail to start while 160 is shown.
  • The machine may not fill, agitate, spin, or drain normally while the fault is active.
Before you call

Safe checks you can make

These are simple, non-hazardous checks only. If anything is unclear, stop and contact a technician.

  • Check that the lid or door is fully closed (and locked, on models with a lid/door lock).
  • Confirm the water supply taps are fully open and hoses are not kinked or restricted.
  • Check that the drain hose is not kinked and the drain/standpipe is clear.
  • Confirm the load is not overloaded or unbalanced.
  • Switch the washer off at the wall, wait about 60 seconds, then switch back on and retry once.
  • Record the full model and serial number from the rating plate.

Important safety warning. Do not open internal panels, remove covers, or access wiring, the motor, or the control board. Do not bypass the lid/door safety switch. If you notice water pooling near electrical parts, a burning smell, or sparks, switch off power at the wall and call a professional immediately.

Get help

When to call a technician

160 on a Fisher & Paykel Washer is best confirmed against your manuals, then assessed by an independent tech if it repeats. Fisher & Paykel Appliance Repair can help with that next step.

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

FAQ

Frequently asked questions

References

Sources & references

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Address 1200 Brickell Ave, Suite 400, Miami, FL 33131
Phone (844) 659-2290
Email service@example.com
Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Miami, New York, Houston, Los Angeles and San Diego metro areas.
Response time Same-day and next-day appointments in most areas.

Request your repair

Fields marked with * are required.

No obligation. We confirm the appointment before any visit or charge.

Call Book diagnosis