Skip to content
Same-day and next-day appointments in most areas.
Specialized Fisher & Paykel repair service. Experienced technicians, genuine parts, service across major U.S. metro areas.
Error Code

Fisher & Paykel Washer Error 37: Pump Blocked

Error code 37
Appliance Washer
Quick answer

Error 37 means the water level stayed the same for over 3 minutes of draining; hose, pump and wiring checks follow.

Model compatibility: Fisher & Paykel reuses codes across series and model years, so 37 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Plain language

What this code means

The water level did not change for over 3 minutes of draining, a pump blocked error.

37 is the pump blocked error on Smartdrive washers of Phases 1 to 6. A drain lasting over 3 minutes while the pressure sensor sends the same level throughout sets it, and the machine reads that as water not leaving.

At a glance

Code 37
What it means The water level did not change for over 3 minutes of draining, a pump blocked error.
What you can check Look at the drain hose for kinks and check that any extension is no more than one piece of 39 in (1 m) with the same diameter. Nothing else is an owner task.
When to call a technician If the hose is fine, a service visit is needed, since the pump has to be inspected with panels off. A tub still full of water needs emptying by the technician.

Why it happens, according to the manual

  • Squeezing or kinking of the drain hose or the pressure switch hose, which slashes the rate at which water is pumped out.
  • Blockage of the pump, whether partial or total.
  • A pump that does not run, caused by the controller module, wiring or the pump failing.
  • Eco machines at Phase 5 and 6 only: the diverter valve is faulty or blocked and stays in recirculation mode, so the level appears untouched by the pump.

Another trigger noted is pumping up to a very tall head of drain hose, or into a hose that has been extended.

Pump system checks, step by step

  1. Make sure the drain hose has no kink.
  2. Confirm its length: at most one extension of 39 in (1 m), same diameter as the hose.
  3. Test the windings of the pump for an open circuit. Its thermal cut-out resets when the pump has cooled down.
  4. When the tub is empty, withdraw the pump from the housing and examine both it and the hose for something blocking them.
  5. When there is water in the tub, servicing is from above in the manual. Take off the top deck and the basket, remove the water by bailing, then lift off the pump’s cap and hood and remove what is restricting it.

Wiring checks come afterwards: the pump harness connection, and its continuity. Both passing, the machine is run in spin by the technician to see whether the pump turns; only a pump that does not turn leads to replacing the Motor Controller. The manual also mentions considering a Pump Hood Kit (WM013).

Who does what

A kinked or overlong hose is the only thing you can look for unaided. After that, panels come off and a tub full of water must be emptied, which is the technician’s part.

Related reading

  • Code 51 is the entry for the diverter valve that the manual points to.
  • Code 44 means water was left in the tub when spinning started.

Drain repair for Fisher & Paykel washers in the Miami, New York, Houston, Los Angeles and San Diego metro areas

Call (844) 659-2290 and say how long your hose is and whether the tub still holds water.

Source: Fisher & Paykel Smartdrive washer service manual 517766 (March 2003), section 19, Detailed Fault Codes

Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

References

Sources & references

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Miami, New York, Houston, Los Angeles and San Diego metro areas.
Response time Same-day and next-day appointments in most areas.
Call Book diagnosis