Skip to content
Same-day and next-day appointments in most areas.
Specialized Fisher & Paykel repair service. Experienced technicians, genuine parts, service across major U.S. metro areas.
Error Code

Fisher & Paykel Washer Code 134: Current Trip with Rotor Error

Error code 134
Appliance Washer
Quick answer

Fault 134 is a combined motor current and rotor position fault listed for Phase 4, with no steps beyond those for 130 and 132.

Model compatibility: Fisher & Paykel reuses codes across series and model years, so 134 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Plain language

What this code means

Fault 134: single current trip and Rotor Position Sensor error detected together, Phase 4.

Only Phase 4 washers carry fault 134. Two events coincided: the Motor Controller module detected excessive motor current and a sensor error from the Rotor Position Sensor. Phase 4 per the manual includes models GW708 and GW608, W508 and MW058, LW085 and AW085, GWC08 and GWM08, GWL08, THM08, and THL08.

At a glance

Code 134
What it means Fault 134: single current trip and Rotor Position Sensor error detected together, Phase 4.
What you can check Isolate the washer at the wall, copy down the number, and mention any earlier 130 or 132 that you saw.
When to call a technician Arrange a check of the machine, since a technician must apply the wiring, motor and rotor sensor procedures together and may need to replace the controller module.

Procedure borrowed from two codes

Nothing is written specifically for 134. The manual’s instruction is to turn to the entries for fault codes 130 and 132 for service.

Taken from 130

Corrosion is sought on the connectors at the Rotor Position Sensor and at the Motor Controller. The hall harness contacts are checked and the sensor tested.

Taken from 132

The wiring between controller and stator is inspected. Resistance of the motor and harness is read against a nominal 12.2 ohm for Phase 4. Water or corrosion at the sensor and stator terminal is looked for, as are leaks that might reach the controller.

Common to both

A replacement Motor Controller module comes last.

Cause of the overlap

Both procedures are to be applied together, and that is the whole instruction. The reason for the two faults occurring at once is not stated.

What owners should do

No owner step appears in the 134 entry. Isolate the washer at the wall, copy down the number and book a check of the Phase 4 model. Mention an earlier 130 or 132, since what the display shows is the most recently recorded fault, according to the manual.

Read next

  • 130: a lone rotor sensor error.
  • 132: a lone current trip.

Washer repair in the metro areas we cover

For Phase 4 Fisher & Paykel washers around Miami, New York, Houston, Los Angeles and San Diego, call (844) 659-2290.

Source: Fisher & Paykel Phase 6 Series 11 (GWL11) service manual 517766, Detailed Fault Codes

Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

References

Sources & references

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Miami, New York, Houston, Los Angeles and San Diego metro areas.
Response time Same-day and next-day appointments in most areas.
Call Book diagnosis