Skip to content
Same-day and next-day appointments in most areas.
Specialized Fisher & Paykel repair service. Experienced technicians, genuine parts, service across major U.S. metro areas.
Error Code

Fisher & Paykel Washer Code 164: Brake Function Time-out

Error code 164
Appliance Washer
Quick answer

A 164 means the washer braked for 20 seconds when spin loads should stop within 10. The manual begins with continuity of the motor wiring.

Model compatibility: Fisher & Paykel reuses codes across series and model years, so 164 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Plain language

What this code means

Brake function time-out: braking lasted 20 seconds; the manual lists the motor wiring first, then the Motor Controller (Phase 4) or Rotor Position Sensor (Phase 5).

At the end of a spin a Fisher & Paykel washer brakes its basket to a stop, and the service manual expects every spin load to be stationary inside 10 seconds. Phase 4 and 5 washers raise code 164, titled “Brake Function Time-out Fault”, when braking by the controller reaches 20 seconds.

At a glance

Code 164
What it means Braking after the spin lasted 20 seconds, pointing first at the motor wiring, then the controller module or the position sensor.
What you can check Turn the washer off, unplug it, keep the cabinet shut, and note whether it showed up after a spin cycle.
When to call a technician Treat this as a service job, as testing the wiring needs a meter and access to the controller end of the harness. A replacement part may be needed after those checks.

Order of suspects

  1. Primary: wiring. Continuity is tested on the motor harness, the connectors and the motor. The test is an ohms reading across the harness phases where the harness meets the controller.
  2. Secondary, once the wiring passes: on a Phase 4 machine the Motor Controller module; on a Phase 5 machine the Rotor Position Sensor (RPS). Either is replaced.

Resistance figures to expect

Phase 2, 3 and 4 12.2 ohms, nominal
Phase 5 Smart Drive 32 ohms, nominal

Notes for the owner

Nothing in the manual is aimed at the owner for this code. Taking the readings calls for a meter and for reaching the controller end of the harness. Turn the washer off, unplug it and book a visit; the cabinet stays shut while the machine is live.

Related motor and brake codes

  • Code 162: the deceleration time-out for braking, marked as a software test code.
  • Code 54: motor current not detected, so the motor is disconnected or the drive has failed.
  • Code 136: the Motor Controller was unable to get the motor started.

Washer repair across our metro areas

For Fisher & Paykel washer repair in Miami, New York, Houston, Los Angeles and San Diego, phone (844) 659-2290. Mention code 164, the model number, and whether it showed up after a spin cycle.

Source: Fisher & Paykel supplementary service manual 517766, section 19 Detailed Fault Codes

Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

References

Sources & references

Code still active?

Have this Fisher & Paykel alert verified on site

Repeating fault codes usually need platform-specific testing. We confirm the cause and price the fix before work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Miami, New York, Houston, Los Angeles and San Diego metro areas.
Response time Same-day and next-day appointments in most areas.
Call Book diagnosis